Nissan Sentra manuals

Nissan Sentra Service Manual: 2135 TP Sensor

Nissan Sentra Service Manual / Engine / Engine control system / Dtc/circuit diagnosis / 2135 TP Sensor

DTC Logic

DTC DETECTION LOGIC

NOTE:

If DTC P2135 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to EC-353, "DTC Logic".

DTC No.

 CONSULT screen terms (Trouble diagnosis content)

 DTC detecting condition

 Possible cause
P2135 TP SENSOR-B1 (Throttle/Pedal position sensor/switch “A” / “B” voltage correlation) Rationally incorrect voltage is sent to ECM compared with the signals from TP sensor 1 and TP sensor 2.
  • Harness or connector (TP sensor 1 or 2 circuit is open or shorted.)
  • Electric throttle control actuator (TP sensor 1 or 2)

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for 1 second.
  2. Check DTC.

Is DTC detected? YES >> Proceed to EC-438, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK THROTTLE POSITION SENSOR POWER SUPPLY

  1. Turn ignition switch OFF.
  2. Disconnect electric throttle control actuator harness connector.
  3. Turn ignition switch ON.
  4. Check the voltage between electric throttle control actuator harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK THROTTLE POSITION SENSOR POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector
  3. Check the continuity between electric throttle control actuator harness connector and ground.


  1. Also check harness for short to ground.

Is the inspection result normal? YES >> Perform the trouble diagnosis for power supply circuit.

NO >> Repair or replace error-detected parts.

3.CHECK THROTTLE POSITION SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check the continuity between electric throttle control actuator harness connector and ECM harness connector.


  1. Also check harness for short to power.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace error-detected parts.

4.CHECK THROTTLE POSITION SENSOR INPUT SIGNAL CIRCUIT

  1. Check the continuity between electric throttle control actuator harness connector and ECM harness connector.


  1. Also check harness for short to ground and to power.

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

5.CHECK THROTTLE POSITION SENSOR

Check throttle position sensor. Refer to EC-439, "Component Inspection (TP Sensor)".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".

NO >> Replace electric throttle control actuator. Refer to EM-27, "Removal and Installation".

Component Inspection (TP Sensor)

1.CHECK THROTTLE POSITION SENSOR

  1. Turn ignition switch OFF.
  2. Reconnect all harness connectors disconnected.
  3. Perform “ Throttle Valve Closed Position Learning”. Refer to EC-139, "Work Procedure".
  4. Turn ignition switch ON.
  5. Set selector lever to D (CVT) or 1st (M/T) position.
  6. Check the voltage between ECM harness connector terminals as per the following conditions.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace electric throttle control actuator. Refer to EM-27, "Removal and Installation".

P2127, P2128 APP Sensor
DTC Logic DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition Possible cause P2127 APP SEN 2/CIRC (Throttle/Pedal p ...

P2138 APP Sensor
DTC Logic DTC DETECTION LOGIC NOTE: If DTC P2138 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to EC-353, "DTC Logic". DTC No. CONSUL ...

Other materials:

Precaution
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of inju ...

Service data and specifications (SDS)
General Specifications Brake Pedal Check Valve Brake Booster Front Disc Brake Rear Drum Brake Rear Disc Brake ...

Special Service Tool
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here. CAUTION: Every time the vehicle is lifted up, maintain the complete vehicle curb condition. Since the vehicle's center of gravity changes when removing main parts on the front si ...

© 2014-2026 Copyright b17.nisentra.com