Nissan Sentra Service Manual: P1652 Starter motor system comm

Nissan Sentra Service Manual / Engine / Engine control system / Dtc/circuit diagnosis / P1652 Starter motor system comm

Description

ECM controls ON/OFF state of the starter relay, according to the engine and vehicle condition. ECM transmits a control signal to IPDM E/R via BCM by CAN communication.

Under normal conditions, ECM controls and maintains the starter relay in OFF state during following condition:

Engine is running.
Selector lever is D position. (CVT models)
Clutch pedal is fully released. (M/T models)

When detecting a decrease in engine speed due to rapid deceleration or heavy load condition, ECM controls and reactivates the starter relay.

IPDM E/R detects a control state of starter relay and starter control relay and transmits a feedback signal to ECM via CAN communication.

DTC Logic

DTC DETECTION LOGIC

NOTE:

If DTC P1652 is displayed with DTC U1001, perform the trouble diagnosis for DTC U1001. Refer to EC-169, "DTC Logic".
If DTC P1652 is displayed with DTC P0607, perform the trouble diagnosis for DTC P0607. Refer to EC-350, "DTC Logic".
If DTC P1652 is displayed with B209F or B20A0 of IPDM E/R, perform the trouble diagnosis for B209F or B20A0. Refer to SEC-118, "DTC Logic" or SEC-120, "DTC Logic".
If DTC P1652 is displayed with B26F9 or B26FA of BCM, perform the trouble diagnosis for B26F9 or B26FA.

Refer to SEC-112, "DTC Logic" or SEC-114, "DTC Logic".

DTC No.	CONSULT screen terms (Trouble diagnosis content)	DTC detecting condition	Possible cause
P1652	STR MTR SYS COMM (Starter motor system communication)	ECM detects malfunction in starter motor drive circuit of the IPDM E/R.	IPDM E/R

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION

Turn ignition switch OFF and wait at least 10 seconds.
Start the engine and wait at least 5 minutes.
Repeat step 1 and 2 for 20 times.
Check DTC.

Is DTC detected? YES >> Proceed to EC-404, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK SELF-DIAGNOSTIC RESULT IN BCM

Check self-diagnostic result in BCM. With CONSULT

Check self-diagnostic result in BCM.

Are any DTC detected? YES >> Check the DTC. Refer to BCS-49, "DTC Index" (with intelligent key), BCS-109, "DTC Index" (without intelligent key).

NO >> GO TO 2.

2.CHECK SELF-DIAGNOSTIC RESULT IN IPDM E/R

Check self-diagnostic result in IPDM E/R. With CONSULT

Check self-diagnostic result in IPDM E/R.

Are any DTC detected? YES >> Check the DTC. Refer to PCS-20, "DTC Index" (with intelligent key), PCS-48, "DTC Index" (without intelligent key).

NO >> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE

Erase DTC.
Perform DTC confirmation procedure again. Refer to EC-404, "DTC Logic".
Check DTC.

Is the P1652 displayed again? YES >> GO TO 4.

NO >> INSPECTION END

4.CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to GI-39, "Intermittent Incident".

Is the inspection result normal? YES >> Replace IPDM E/R. Refer to PCS-58, "Removal and Installation".

NG >> Repair or replace error-detected parts.

P1651 Starter motor relay

Description ECM controls ON/OFF state of the starter relay, according to the engine and vehicle condition. ECM transmits a control signal to IPDM E/R by CAN communication. Under normal conditio ...

P1715 Input speed sensor

Description ECM receives input speed sensor signal from TCM through CAN communication line. ECM uses this signal for engine control. DTC Logic DTC DETECTION LOGIC NOTE: If DTC P1715 is disp ...

Other materials:

Engine coolant temperature gauge
NOTE: The ignition switch must be placed in the ON position for the gauge to give a reading. The gauge indicates the engine coolant temperature. The engine coolant temperature is within the normal range when the reading is within the zone A shown in the illustration. The engine coolan ...

Precaution
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as вЂњAIR BAGвЂќ and вЂњSEAT BELT PRE-TENSIONERвЂќ, used along with a front seat belt, helps to reduce the risk or severity of injury ...

Basic inspection
Diagnosis and repair work flow Work Flow Overall sequence Detailed flow 1. Get information for symptom Get the detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurred). >> Go to 2. 2. Check dtc Check ...