Nissan Sentra manuals

Nissan Sentra Service Manual: P0340 CMP Sensor (PHASE)

Nissan Sentra Service Manual / Engine / Engine control system / Dtc/circuit diagnosis / P0340 CMP Sensor (PHASE)

DTC Logic

DTC DETECTION LOGIC

DTC No.

 CONSULT screen terms (Trouble diagnosis content)

 DTC detecting condition

 Possible cause
P0340 CMP SEN/CIRC-B1 (Camshaft position sensor “A” circuit bank 1)
  • The cylinder No. signal is not sent to ECM for the first few seconds during engine cranking.
  • The cylinder No. signal is not sent to ECM during engine running
  • The cylinder No. signal is not in the normal pattern during engine running.
  • Harness or connectors (Camshaft position sensor circuit is open or shorted)
  • Camshaft position sensor
  • Camshaft (Intake)
  • Starter motor
  • Starting system circuit
  • Dead (Weak) battery
  • Sensor power supply 2 circuit

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 10.5 V with ignition switch ON.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE-1

  1. Start engine and let it idle for at least 5 seconds.

    If engine does not start, crank engine for at least 2 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Proceed to EC-280, "Diagnosis Procedure".

NO >> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE-2

  1. Maintaining engine speed at more than 800 rpm for at least 5 seconds.
  2. Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Proceed to EC-280, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK STARTING SYSTEM

Turn ignition switch to START position.

Does the engine turn over? Does the starter motor operate? YES >> GO TO 2.

NO >> Check starting system. Refer to STR-20, "Work Flow (With GR8-1200 NI)" or STR-24, "Work Flow (Without GR8-1200 NI)".

2.CHECK CAMSHAFT POSITION (CMP) SENSOR (PHASE) POWER SUPPLY

  1. Turn ignition switch OFF
  2. Disconnect camshaft position (CMP) sensor (PHASE) harness connector.
  3. Turn ignition switch ON.
  4. Check the voltage between CMP sensor (PHASE) harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> GO TO 3.

3.CHECK SENSOR POWER SUPPLY 2 CIRCUIT

Check sensor power supply 2 circuit. Refer to EC-444, "Diagnosis Procedure".

Is inspection result normal? YES >> Perform the trouble diagnosis for power supply circuit.

NO >> Repair or replace error-detected parts.

4.CHECK CMP SENSOR (PHASE) GROUND CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector
  3. Check the continuity between CMP sensor (PHASE) harness connector and ECM harness connector.


  1. Also check harness for short to power.

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace error-detected parts.

5.CHECK CMP SENSOR (PHASE) INPUT SIGNAL CIRCUIT

  1. Disconnect ECM harness connector.
  2. Check the continuity between CMP sensor (PHASE) harness connector and ECM harness connector.


  1. Also check harness for short to ground and to power.

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace error-detected parts.

6.CHECK CAMSHAFT POSITION SENSOR (PHASE)

Check the camshaft position sensor (PHASE). Refer to EC-282, "Component Inspection [CMP Sensor (PHASE)]".

Is the inspection result normal?

YES >> GO TO 7.

NO >> Replace camshaft position sensor (PHASE). Refer to EM-60, "Removal and Installation".

7.CHECK CAMSHAFT (INT)

Check the following.

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".

NO >> Remove debris and clean the signal plate of camshaft rear end or replace camshaft. Refer to EM-60, "Removal and Installation".

Component Inspection [CMP Sensor (PHASE)]


Component Inspection [CMP Sensor (PHASE)]

1.CHECK CAMSHAFT POSITION SENSOR (PHASE)-1

  1. Turn ignition switch OFF.
  2. Loosen the fixing bolt of the sensor
  3. Disconnect camshaft position sensor (PHASE) harness connector.
  4. Remove the sensor.
  5. Visually check the sensor for chipping.

Is the inspection result normal? YES >> GO TO 2.

NO >> Replace camshaft position sensor (PHASE). Refer to EM-60, "Removal and Installation".

2.CHECK CAMSHAFT POSITION SENSOR (PHASE)-2


2.CHECK CAMSHAFT POSITION SENSOR (PHASE)-2

Check the resistance camshaft position sensor (PHASE) terminals as per the following.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace camshaft position sensor (PHASE). Refer to EM-60, "Removal and Installation".

P0335 CKP Sensor (POS)
DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0340 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to EC- 353, "DTC Logic". DTC No. CONSU ...

P0420 Three way catalyst function
DTC Logic DTC DETECTION LOGIC The ECM monitors the switching frequency ratio of air fuel ratio (A/F) sensor 1 and heated oxygen sensor 2. A three way catalyst (manifold) with high oxygen storage ...

Other materials:

P0117, P0118 ECT Sensor
DTC Logic DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition Possible cause P0117 ECT SEN/CIRC (Engine coolant temperature sensor 1 circuit low) An excessively low voltage from the engine coolant temperatu ...

Fuel level sensor unit, fuel filter and fuel pump assembly
Exploded View Lock ring Fuel level sensor, fuel filter and fuel pump assembly O-ring Fuel tank Removal and Installation WARNING: Read “General Precautions” when working on the fuel system. Refer to FL-2, "General Precaution". NOTE: When removing componen ...

P0998 Shift solenoid F
DTC Logic DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition Possible causes P0998 SHIFT SOLENOID F (Shift Solenoid F Control Circuit Low) The TCM low brake solenoid valve current monitor reading is 200 mA or ...

© 2014-2026 Copyright b17.nisentra.com