Nissan Sentra Service Manual: Interior room lamp control circuit
Description
Controls each interior room lamp (ground side) by pwm signal.
Note:
Pwm signal control period is approximately 250 hz (in the gradual brightening/dimming).
Component function check
Caution:
Before performing the diagnosis, check that the following are normal.
- Interior room lamp power supply
- Room lamp bulb
- Map lamp bulb
1.Check interior room lamp control function
Consult active test
- Se the map lamp switch or room lamp switch to door.
- Turn ignition switch on.
- Select int lamp of bcm (int lamp) active test item.
- While operating the test items, check that each interior room lamp turns ON/OFF (gradual brightening/ dimming).
On : interior room lamp gradual brightening
Off : interior room lamp gradual dimming
Does the interior room lamp turns ON/OFF (gradual brightening/dimming)? YES >> Interior room lamp control circuit is normal.
NO >> Refer to INL-45, "Diagnosis Procedure".
Diagnosis procedure
Regarding Wiring Diagram information, refer to INL-17, "Wiring Diagram".
1.Check interior room lamp control output
Consult active test
- Turn ignition switch OFF
- Remove all the bulbs of room lamp and map lamp.
- Turn ignition switch on.
- Select int lamp of bcm (int lamp) active test item.
- While operating the test item, check continuity between BCM harness connector and ground.
Is the inspection result normal? Yes >> interior room lamp control circuit is operating normally.
Fixed on>>go to 3.
Fixed off>>go to 2.
2.Check interior room lamp control open circuit
- Turn ignition switch off.
- Disconnect bcm connector and room lamp and map lamp connector.
- Check continuity between BCM harness connector and room lamp harness connector.
Is the inspection result normal? Yes >> check interior room lamps for an open. If ng, replace lamp in question. Refer to inl-55, "removal and installation" (room lamp) or inl-52, "removal and installation" (map lamp). If ok, replace bcm. Refer to bcs-73, "removal and installation" (with intelligent key), bcs-126, "removal and installation" (without intelligent key).
No >> repair or replace harness or connector.
3.Check interior room lamp control short to ground
- Turn ignition switch off.
- Disconnect BCM connector.
- Check continuity between BCM harness connector and ground.
Is the inspection result normal? Yes >> check interior room lamps for an internal short to ground. If ng, replace lamp in question. Refer to inl-55, "removal and installation" (room lamp) or inl-52, "removal and installation" (map lamp). If ok, replace bcm. Refer to bcs-73, "removal and installation" (with intelligent key), bcs-126, "removal and installation" (without intelligent key).
No >> repair or replace harness or connector.
Battery saver output/power supply circuit
Description
Provides the battery saver output/power supply. Also cuts the power supply
when the interior lamp battery
saver is activated.
Component function check
1.Check battery saver output/po ...
Trunk room lamp circuit
Description
Controls the trunk room lamp (ground side) to turn the trunk room lamp on and
off.
Diagnosis Procedure
Regarding wiring diagram information, refer to inl-17, "wiring diagram" ...
Other materials:
Trunk room trim
Exploded View
Trunk floor trim
Trunk front floor spacer (LH)
Trunk side finisher (LH)
Reflector box assembly*
Trunk rear plate
Trunk side finisher (RH)
Trunk front floor spacer (RH)
Clip
Pawl
Trunk rear plate
TRUNK REAR PLATE : Removal and Installation
REMOVAL
Remove ...
Precaution
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER"
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”,
used along
with a front seat belt, helps to reduce the risk or severity of injur ...
Exhaust gas (carbon monoxide)
WARNINGDo not breathe exhaust gases; they
contain colorless and odorless carbon
monoxide. Carbon monoxide is dangerous.
It can cause unconsciousness or
death.
If you suspect that exhaust fumes are
entering the vehicle, drive with all windows
fully open, and have ...
