Nissan Sentra manuals

Nissan Sentra Service Manual: P0130 A/F Sensor 1

Nissan Sentra Service Manual / Engine / Engine control system / Dtc/circuit diagnosis / P0130 A/F Sensor 1

DTC Logic

DTC DETECTION LOGIC

To judge the malfunction, the diagnosis checks that the A/F signal computed by ECM from the A/F sensor 1 signal fluctuates according to fuel feedback control.

DTC No.

 CONSULT screen terms (Trouble diagnosis content)

 DTC detecting condition

 Possible cause
P0130 A/F SENSOR1 (B1) (O2 sensor circuit bank 1 sensor 1) A) The A/F signal computed by ECM from the A/F sensor 1 signal is constantly in the range other than approx. 2.2 V.
  • Harness or connectors (A/F sensor 1 circuit is open or shorted.)
  • A/F sensor 1
B) The A/F signal computed by ECM from the A/F sensor 1 signal is constantly approx. 2.2 V.

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

  1. If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
  2. Turn ignition switch OFF and wait at least 10 seconds.
  3. Turn ignition switch ON.
  4. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A

With CONSULT


  1. Start engine and warm it up to normal operating temperature.
  2. Let it idle for 2 minutes.
  3. Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Proceed to EC-211, "Diagnosis Procedure".

NO-1 ( With CONSULT)>>GO TO 3.


NO-2 ( 3.CHECK AIR FUEL RATIO (A/F) SENSOR 1 FUNCTION Without CONSULT)>>GO TO 7.


3.CHECK AIR FUEL RATIO (A/F) SENSOR 1 FUNCTION

  1. Select “A/F SEN1 (B1)” in “DATA MONITOR” mode of “ENGINE” using CONSULT.
  2. Check “A/F SEN1 (B1)” indication.

Does the indication fluctuates around 2.2 V? YES >> GO TO 4.

NO >> Proceed to EC-211, "Diagnosis Procedure".

4.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B-1

  1. Select “A/F SEN1 (B1) P1276” of “A/F SEN1” in “DTC WORK SUPPORT” mode of “ENGINE” using CONSULT.
  2. Touch “START”.
  3. When the following conditions are met, “TESTING” will be displayed on the CONSULT screen.

If “TESTING” is not displayed after 20 seconds, retry from step 2.


If “TESTING” is not displayed after 20 seconds, retry from step 2.

CAUTION:

Always drive vehicle at a safe speed.

Is “TESTING” displayed on CONSULT screen? YES >> GO TO 5.

NO >> 1. Check A/F sensor 1 function again.

2. GO TO 3.

5.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B-2

Release accelerator pedal fully.

NOTE:

Never apply brake during releasing the accelerator pedal.

Which does “TESTING” change to? COMPLETED>>GO TO 6.

OUT OF CONDITION>>1.Retry DTC CONFIRMATION PROCEDURE.

2. GO TO 4.

6.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B-3

Touch “SELF-DIAG RESULT” Which is displayed on CONSULT screen? YES >> INSPECTION END

NO >> Proceed to EC-211, "Diagnosis Procedure".

7.PERFORM COMPONENT FUNCTION CHECK FOR MALFUNCTION B

Perform Component Function Check. Refer to EC-211, "Component Function Check".

NOTE:

Use component function check to check the overall function of the A/F sensor 1 circuit. During this check, a 1st trip DTC might not be confirmed.

Is the inspection result normal? YES >> INSPECTION END

NO >> Proceed to EC-211, "Diagnosis Procedure".

Component Function Check

1.PERFORM COMPONENT FUNCTION CHECK

With GST


  1. Start engine and warm it up to normal operating temperature.
  2. Drive the vehicle at a speed of 80 km/h (50 MPH) for a few minutes in the suitable gear position.
  3. Shift the selector lever to the D position (CVT) or 5th position (M/T), then release the accelerator pedal fully until the vehicle speed decreases to 50 km/h (31 MPH).

CAUTION:

Always drive vehicle at a safe speed.

NOTE:

Never apply brake during releasing the accelerator pedal.

  1. Repeat steps 2 to 3 for five times.
  2. Stop the vehicle and turn ignition switch OFF.
  3. Wait at least 10 seconds and restart engine.
  4. Repeat steps 2 to 3 for five times
  5. Stop the vehicle.
  6. Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Proceed to EC-211, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY

  1. Turn ignition switch OFF.
  2. Disconnect A/F sensor 1 harness connector.
  3. Turn ignition switch ON.
  4. Check the voltage between A/F sensor 1 harness connector and ground.

*1: Except California


*1: Except California

*2: For California

Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect IPDM E/R harness connector
  3. Check the continuity between A/F sensor 1 harness connector and IPDM E/R harness connector.

*1: Except California


*1: Except California

*2: For California

  1. Also check harness for short to ground.

Is the inspection result normal? YES >> Perform the trouble diagnosis for power supply circuit.

NO >> Repair or replace error-detected parts.

3.CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check the continuity between A/F sensor 1 harness connector and ECM harness connector.

*1: Except California


*1: Except California

*2: For California

  1. Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector and ground.

*1: Except California


*1: Except California

*2: For California


  1. Also check harness for short to power.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace error-detected parts.

4.CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to GI-39, "Intermittent Incident".

Is the inspection result normal? YES >> Replace air fuel ratio (A/F) sensor 1. Refer to EM-30, "Exploded View".

NO >> Repair or replace error-detected parts.

P0128 Thermostat function
DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0128 is displayed with DTC P0300, P0301, P0302, P0303 or P0304, first perform the trouble diagnosis for P0300, P0301, P0302, P0303 or P0304. Refer to ...

P0131 A/F Sensor 1
DTC Logic DTC DETECTION LOGIC To judge the malfunction, the diagnosis checks that the A/F signal computed by ECM from the A/F sensor 1 signal is not inordinately low. DTC No. CONSULT s ...

Other materials:

Headlamp (hi) circuit
Description The IPDM E/R (intelligent power distribution module engine room) controls the headlamp high relay based on inputs from the BCM over the CAN communication lines. When the headlamp high relay is energized, power flows through fuses 41 and 42, located in the IPDM E/R. Power then flo ...

Dtc/circuit diagnosis
Malfunction area chart Main line Branch line Short circuit Main line between ipdm-e and dlc circuit Diagnosis procedure 1.Check connector Turn the ignition switch off. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors fo ...

Service data and specifications (SDS)
General Specifications Clutch Pedal Clutch Disc Clutch Cover ...

© 2014-2026 Copyright b17.nisentra.com