Nissan Sentra Service Manual: P0643 Sensor power supply

Nissan Sentra Service Manual / Engine / Engine control system / Dtc/circuit diagnosis / P0643 Sensor power supply

Description

ECM supplies a voltage of 5.0 V to some of the sensors systematically divided into 2 groups, respectively.

Accordingly, when a short circuit develops in a sensor power source, a malfunction may occur simultaneously in the sensors belonging to the same group as the shorted-circuit sensor.

Sensor power supply 1

Battery current sensor
Crankshaft position (CKP) sensor (POS)
Throttle position (TP) sensor
Accelerator pedal position (APP) sensor 1

NOTE:

If sensor power supply 1 circuit is malfunctioning, DTC P0643 is displayed.

Sensor power supply 2

Camshaft position (CMP) sensor (PHASE)
Mass air flow (MAF) sensor
Engine oil pressure (EOP) sensor
Exhaust valve timing (EVT) control position sensor
Accelerator pedal position (APP) sensor 2
Intake manifold runner control valve position sensor

DTC Logic

DTC DETECTION LOGIC

DTC No.	CONSULT screen terms (Trouble diagnosis content)	DTC detecting condition	Possible cause
P0643	SENSOR POWER/CIRC (Sensor reference voltage ″A″ circuit high)	ECM detects that the voltage of sensor power supply 1 is excessively low or high.	Harness or connectors (Battery current sensor circuit is shorted.) (CKP sensor circuit is shorted.) (TP sensor circuit is shorted.) (Refrigerant pressure sensor circuit is shorted.) (APP sensor 1 circuit is shorted.) Battery current sensor CKP sensor TP sensor Refrigerant pressure sensor APP sensor

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDUR

Start engine and let it idle for 1 second.
Check DTC.

Is DTC detected? YES >> Refer to EC-354, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK ACCELERATOR PEDAL POSITION SENSOR 1 POWER SUPPLY CIRCUIT

Disconnect accelerator pedal position (APP) sensor harness connector.
Turn ignition switch ON.
Check the voltage between APP sensor harness connector and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 4.

NO >> GO TO 2.

2.CHECK SENSOR POWER SUPPLY CIRCUITS

Check harness for short to power and short to ground, between the following terminals.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair short to ground or short to power in harness or connectors.

3.CHECK COMPONENTS

Check the following.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace malfunctioning component.

4.CHECK APP SENSOR

Check APP sensor. Refer to EC-433, "Component Inspection (APP Sensor)".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".

NO >> Replace accelerator pedal assembly. Refer to ACC-3, "Removal and Installation".

P060B ECM

DTC Logic DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition Possible cause P060B CONTROL MODULE (Internal control ...

P0850 PNP Switch

Description For CVT models, transmission range switch is turn ON when the selector lever is P or N. For M/T models, park/neutral position (PNP) range switch is ON when the selector lever is Ne ...

Other materials:

P2858 Clutch B Pressure
DTC Logic DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition Possible causes P2858 CLUTCH B PRESSURE (Clutch B Pressure Engagement Performance) The auxiliary gearbox gear ratio is 2.232 or more for the auxiliary gearbox 2GR ratio ...

Unit disassembly and assembly
Front coil spring and strut Exploded View Piston rod lock nut Strut mount insulator Strut mount bearing Bound bumper Coil spring Lower rubber seat Strut Steering knuckle Front Disassembly and Assembly DISASSEMBLY CAUTION: Do not damage the piston rod when removing comp ...

Clutch fluid
Inspection FLUID LEAKAGE Check clutch line for cracks, deterioration or other damage. Replace any damaged parts. Check for fluid leakage by fully depressing clutch pedal while engine is running. CAUTION: If leakage occurs around connections, reinstall the lines or replace damaged ...