Nissan Sentra manuals

Nissan Sentra Service Manual: P0037, P0038 HO2S2 Heater

Nissan Sentra Service Manual / Engine / Engine control system / Dtc/circuit diagnosis / P0037, P0038 HO2S2 Heater

DTC Logic

DTC DETECTION LOGIC

DTC No.

 CONSULT screen terms (Trouble diagnosis content)

 DTC detecting condition

 Possible cause
P0037 HO2 HTR (B1) (HO2S heater control circuit low bank 1 sensor 2) The current amperage in the heated oxygen sensor 2 heater circuit is out of the normal range.

(An excessively low voltage signal is sent to ECM through the heated oxygen sensor 2 heater.)
  • Harness or connectors (Heated oxygen sensor 2 heater circuit is open or shorted.)
  • Heated oxygen sensor 2 heater
P0038 HO2 HTR (B1) (HO2S heater control circuit high bank 1 sensor 2) The current amperage in the heated oxygen sensor 2 heater circuit is out of the normal range.

(An excessively high voltage signal is sent to ECM through the heated oxygen sensor 2 heater.)
  • Harness or connectors (Heated oxygen sensor 2 heater circuit is shorted.)
  • Heated oxygen sensor 2 heater

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT


  1. Turn ignition switch ON and select “DATA MONITOR” mode of “ENGINE” using CONSULT.
  2. Start engine and warm it up to normal operating temperature.
  3. Turn ignition switch OFF and wait at least 10 seconds.
  4. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load
  5. Let engine idle for 1 minute.
  6. Check 1st trip DTC.

Follow the procedure “With CONSULT” above.With GST


Follow the procedure “With CONSULT” above.

Is 1st trip DTC detected?

YES >> Proceed to EC-178, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK HO2S2 POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect heated oxygen sensor 2 (HO2S2) harness connector.
  3. Turn ignition switch ON.
  4. Check the voltage between HO2S2 harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace error-detected parts.

2.CHECK HO2S2 OUTPUT SIGNAL CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check the continuity between HO2S2 harness connector and ECM harness connector.


  1. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace error-detected parts.

3.CHECK HEATED OXYGEN SENSOR 2 HEATER

Check the heated oxygen sensor 2 heater. Refer to EC-179, "Component Inspection (HO2S Heater)".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".

NO >> Replace heated oxygen sensor 2. Refer to EX-5, "Exploded View".

Component Inspection (HO2S Heater)

1.CHECK HEATED OXYGEN SENSOR 2 HEATER

  1. Turn ignition switch OFF.
  2. Disconnect heated oxygen sensor 2 (HO2S2) harness connector.
  3. Check resistance between HO2S2 terminals as per the following

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace heated oxygen sensor 2. Refer to EX-5, "Exploded View".

P0031, P0032 A/F sensor 1 Heater
DTC Logic DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition Possible cause P0031 A/F SEN 1 HTR (B1) (HO2S heater ...

P0075 IVT control solenoid valve
DTC Logic DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition Possible cause P0075 INT/V TIM V/CIR-B1 (Intake valve ...

Other materials:

Control buttons
The control buttons for the Bluetooth® Hands-Free Phone System are located on the steering wheel. PHONE/SEND Press the   button to initiate a VR session or answer an incoming call. You can also use the button to interrupt the system feedback and give a command at once. See “L ...

P2101 Electric throttle control function
DTC Logic DTC DETECTION LOGIC NOTE: If DTC P2101 is displayed with DTC P2100, first perform the trouble diagnosis for DTC P2100. Refer to EC-423, "DTC Logic". If DTC P2101 is displayed with DTC P2119, first perform the trouble diagnosis for DTC P2119. Refer to EC-430, &qu ...

Battery saver output/power supply circuit
Description Provides the battery saver output/power supply. Also cuts the power supply when the interior lamp battery saver is activated. Component function check 1.Check battery saver output/power supply function Consult Turn ignition switch on. Turn each interior lamp to the ON posit ...

© 2014-2026 Copyright b17.nisentra.com