Nissan Sentra Service Manual: C1716, C1717, C1718, C1719 Transmitter (pressure data)

Nissan Sentra Service Manual / Suspension / Road wheels & Tires / DTC/Circuit diagnosis / C1716, C1717, C1718, C1719 Transmitter (pressure data)

DTC Logic

NOTE:

The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.

Activate and display TPMS transmitter IDs
Display tire pressure reported by the TPMS transmitter
Read TPMS DTCs
Register TPMS transmitter IDs

DTC DETECTION LOGIC

DTC	Display Item	Malfunction detected condition	Possible causes
C1716	[PRESSDATA ERR] FL	Malfunction in the tire pressure data from the front LH wheel transmitter.	Transmitter ID registration incomplete Transmitter malfunction
C1717	[PRESSDATA ERR] FR	Malfunction in the tire pressure data from the front RH wheel transmitter.
C1718	[PRESSDATA ERR] RR	Malfunction in the tire pressure data from the rear RH wheel transmitter.
C1719	[PRESSDATA ERR] RL	Malfunction in the tire pressure data from the rear LH wheel transmitter.

DTC CONFIRMATION PROCEDURE

1.PERFORM SELF DIAGNOSTIC RESULT

With CONSULT

Turn the ignition switch ON.
Check the tire pressure for all wheels and adjust to the specified value. Refer to WT-54, "Tire Air Pressure".
Perform вЂњSELF DIAGNOSTIC RESULTвЂќ.

Is DTC вЂњC1716вЂќ, вЂњC1717вЂќ, вЂњC1718вЂќ, or вЂњC1719вЂќ detected? YES >> Proceed to WT-30, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

NOTE:

The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.

Activate and display TPMS transmitter IDs
Display tire pressure reported by the TPMS transmitter
Read TPMS DTCs
Register TPMS transmitter IDs

1.CHECK TIRE PRESSURE

Check the air pressure of all wheels. Refer to pressure observed during вЂњDTC CONFIRMATION PROCEDUREвЂќ.

Is the inspection result normal? YES >> Replace the DTC-detected malfunctioning transmitter. Refer to WT-50, "Removal and Installation".

NO >> GO TO 2.

2.CHECK TIRE PRESSURE SIGNAL

With CONSULT

Perform transmitter ID registration for all wheels. Refer to WT-22, "Work Procedure".
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
Stop the vehicle.
On вЂњDATA MONITORвЂќ select вЂњAIR PRESS FLвЂќ, вЂњAIR PRESS FRвЂќ, вЂњAIR PRESS RRвЂќ and вЂњAIR PRESS RLвЂќ.
Within 5 minutes after vehicle is stopped, read the values displayed on CONSULT.

Are tire pressures displayed as 438.6 kPa (4.47 kg/cm2, 63.6 psi)? YES >> Replace transmitter for the tire that displayed pressure as 438.6 kPa (4.47 kg/cm2, 63.6 psi).

Refer to WT-50, "Removal and Installation".

NO >> Perform вЂњDTC CONFIRMATION PROCEDUREвЂќ again. Refer to WT-30, "DTC Logic".

C1708, C1709, C1710, C1711 Transmitter (no data)

DTC Logic NOTE: The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information. Activate and display TPMS ...

C1729 Vehicle speed signal

DTC Logic NOTE: The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information. Activate and display TPMS ...

Other materials:

Radio
With the ignition placed in the ACC or ON position, press the PWR (power)/VOL (volume) knob to turn the radio on. If you listen to the radio with the engine not running, the ignition should be placed in the ACC position. Radio reception is affected by station signal strength, distance from r ...

Door outside molding
Exploded view Front door assembly Grommet Front door outside molding Rear door outside molding Rear door assembly Door glass Clip Front door outside molding FRONT DOOR OUTSIDE MOLDING : Removal and Installation REMOVAL Remove front door mirror. Refer to MIR-18, &quo ...

Power supply and ground circuit
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM) BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM) : Diagnosis Procedure Regarding Wiring Diagram information, refer to BCS-51, "Wiring Diagram". 1.Check fuses and fusible link Check that the following fuses and fusible link ...