Nissan Sentra manuals

Nissan Sentra Service Manual: P2765 Input speed sensor B

Nissan Sentra Service Manual / Transmission & driveline / Transaxle & transmission / CVT: RE0F11A / P2765 Input speed sensor B

DTC Logic

DTC DETECTION LOGIC

DTC

 CONSULT screen terms (Trouble diagnosis content)

 DTC detection condition

 Possible causes
P2765 INPUT SPEED SENSOR B (Input/Turbine Speed Sensor B Circuit) The secondary speed sensor value is less than 150 rpm continuously for 5 seconds or more under the following diagnosis conditions:

Diagnosis conditions

  • Primary pulley speed: 1,000 rpm or more
  • TCM power supply voltage: More than 11 V
  • Harness or connector (Secondary speed sensor circuit is open or shorted)
  • Secondary speed sensor
The secondary pulley speed sensor value is 240 rpm or less continuously for 500 msec or more under the following diagnosis conditions:

Diagnosis condition

  • 10-msec-ago secondary pulley speed: 1,000 rpm or more
  • TCM power supply voltage: More than 11 V

DTC CONFIRMATION PROCEDURE

CAUTION:

Be careful of the driving speed.

1.PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

  1. Start the engine
  2. Drive the vehicle
  3. Maintain the following conditions for 10 seconds or more.

Selector lever : “D” position

Vehicle speed : 55 km/h (34 MPH) or more

  1. Stop the vehicle.
  2. Check the first trip DTC.

Is “P2765” detected? YES >> Go to TM-223, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK SECONDARY SPEED SENSOR POWER CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect secondary speed sensor connector.
  3. Turn ignition switch ON.
  4. Check voltage between secondary speed sensor harness connector terminal and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 2.

NO >> GO TO 6.

2.CHECK SECONDARY SPEED SENSOR GROUND CIRCUIT

Check continuity between of secondary speed sensor harness connector terminal and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace malfunctioning parts.

3.CHECK CIRCUIT BETWEEN SECONDARY SPEED SENSOR AND TCM (PART 1)

  1. Turn ignition switch OFF.
  2. Disconnect TCM connector.
  3. Check continuity between secondary speed sensor harness connector terminal and TCM harness connector terminal.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace malfunctioning parts.

4.CHECK CIRCUIT BETWEEN SECONDARY SPEED SENSOR AND TCM (PART 2)

Check continuity between secondary speed sensor harness connector terminal and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace malfunctioning parts.

5.Check TCM Input signals

  1. Connect all of disconnected connectors.
  2. Lift the vehicle.
  3. Start the engine.
  4. Check frequency of secondary speed sensor.

Is the inspection result normal?


Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".

NO >> Replace secondary speed sensor. TM-269, "Removal and Installation".

6.DETECT MALFUNCTIONING ITEMS

Check the following items:

Is the check result normal? YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".

NO >> Repair or replace malfunctioning parts.

P1588 G Sensor
DTC Logic DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition Possible causes P1588 G Sensor (Gravity S ...

P2857 Clutch A Pressure
DTC Logic DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition Possible causes P2857 CLUTCH A PRESSURE (Clutch A Pressu ...

Other materials:

P0604 ECM
DTC Logic DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition Possible cause P0604 ECM [Internal control module random access memory (RAM) error] Malfunction in the internal RAM of ECM. ECM DTC CON ...

Interior room lamp
Removal and installation Removal Insert a suitable tool into the gap between the headlining and the interior room lamp and release the interior room lamp. Disconnect the harness connector from the interior room lamp. Installation Installation is in the reverse order of removal. Bul ...

Rear disc brake
BRAKE PAD BRAKE PAD : Exploded View Upper sliding pin bolt Lower sliding pin bolt Bushing Cylinder body Inner shim cover Inner shim Inner pad (with pad wear sensor) Pad retainer Torque member Outer pad Outer shim Outer shim cover Apply rubber grease Molykote A ...

© 2014-2026 Copyright b17.nisentra.com